Plastic Part Design & Manufacturing Company – bring your products to market from product ideas
Stebro Mold is a Chinese plastic product design and development company with in house mold manufacturing and injection molding capabilities. We mainly make plastic part design, mold making and custom injection molding manufacturing for consumer products, electronic products, medical devices, housewares, and outdoor power equipment. Different from other plastic design company or design agency, we not only can help you on new plastics product development, reverse engineering on the existing product, but also can help you to do the rapid prototype, mold design, mold making, injection molding, and contract part assembly.
Plastic Engineering Support You Can Count On
When you do the injection-molded plastic design, you face many constraints: time-to-market pressure, budget limits, material selection, moldability, tooling expense, minimal engineering changes, and tool qualification time. New product development starts with an idea and it is profitable to invole Stebro Mold as early as possible. We support you in product development, and we orient in the mold design to the specific needs of your products and processes. FEM and filling, warpage, cooling and flow analyzes help to create the optimization of constructive measures. Modern technologies offer new options to maximize service life and minimize cycle times. Our goal is to help you with the design of plastic components that is to your specifications and manufacturable.
What is the manufacturing process for the plastic parts?
When we do the plastic component design, the manufacturing process is an important consideration. The goal is to achieve a technically accurate design that functions well and can manufacture cost-effectively. There are many ways to make plastic components, casting, compression molding, CNC manufacturing, extrusion, blow molding, thermoforming, rotational molding, and injection molding. At Stebro Mold, we use injection molding as the primary manufacturing process to bring plastic products to life.
How to do the plastic part design for Injection Molding?
The plastic product design process offers many versatile solutions and unique benefits, but it’s a practice that depends on the strength of its design. The injection molding part design must be developed to maximize the efficiency inherent in high-volume molding. Plastic product and mold design, tool building, plastic material selection, and Injection molding manufacturing process are the four key factors that go into making a high-quality plastic injection molded part. During both the injection and cooling stages of the manufacturing process, below are several factors that may affect the quality of the final product and the repeatability of the manufacturing process.
1, Use uniform wall thickness
Use a uniform wall thickness throughout the part (if possible) is essential to avoid thick sections. Wall thickness between 1.2 mm and 3 mm is a safe value for most materials. The next table summaries specific recommended wall thicknesses for some of the most common Injection Molding materials:
If sections of different thicknesses are required, make the transition as smooth as possible using a chamfer or fillet. In this way, the material filling will be much better.
The wall thickness specified typically should meet application requirements, moldability, and agency requirements. From a cost standpoint, the thinnest wall utilizes the least material and results in the fastest molding cycle times.
2, Rib Design
Ribs increase the moment of inertia in a design, which in turn will increase the bending stiffness of a part without adding thickness. Rib should not exceed 70% nor lower 50% of part wall thickness; both scenarios can cause sinking in the surface of your part. We also have to pay attention to the rib height, location, and degree of the draft for ease of ejection. Proper rib design involves five main issues: thickness, height, location, quantity, and moldability.
3, Boss design
A boss is included in the part design to accommodate part assembly through screws or pins. Generally, the thickness should be as same as the ribs. The outside diameter of the bosses should remain within 2.0 to 2.4 times the outer diameter of the screw or insert. Thicker bosses will create sink defects as the part cools, but a boss-rib combination can eliminate sink marks. By using ribs to connect the boss to a side wall, this method of part design will provide the strength necessary to support screws and inserts. Also, adding small radii to break the sharp corners will significantly reduce stress concentrations. And as with ribs, the boss also needs to have some draft to aid in ejection.
Usually, the boss hole should extend to the base-wall level, even if the full depth is not needed for assembly. If the boss hole is too long, we may have filling problems, knit lies, or surface blemishes. If the boss hole is too short, we may have a sink mark on the part surface.
4, Draft Angles
Draft angles must be included in the design. It allows you to remove the part from a mold. The draft needs to be in an offset angle, parallel to the opening and closing of the mold. Surfaces formed by slides may not need a draft angel if the steel separates from the surface before ejection. The mold finish, resin, part geometry, and mold ejection system determine the amount of draft needed. Generally, polished mold surfaces require less draft angel than surfaces with machined finishes. When you allow for as much draft angel as possible, you make it easier to release parts from the mold. One or two degrees of drafts, along with 1.5 degrees per .25 millimeters depth of texture, should enough.
Other factors need to be considered when you do the plastics engineered product design for the injection molding, such as parting lines, threaded fasteners, snap-fit joints, living Hinges, and undercuts. Avoiding undercuts altogether might be the best option in molding design. Undercuts always increase the mold cost, complexity, and maintenance requirements of the mold. A smart redesign can often eliminate undercuts.
Selecting the Right Plastic Material for Your Next Injection Molded Product
Plastic raw material can dramatically affect your plastic part’s tensile strength, temperature resistance, appearance, lifespan, and cost. When considering plastics injection molding materials for your product, there are many properties to consider. Aligning with your injection molding manufacturing partner to choose the proper material for the injection molded part is one of the most critical elements of good design.
Stebro Mold Engineering Capabilities Including:
- Product Design
- Engineering assistance for product design.
- Raw Material Selection
- Design Reformation / Reverse Engineering
- Mold flow analysis
- Design optimization for enhanced mould life.
- Design for Manufacturing/Assembly
- 2D/3D Part Design
- 2D/3D Mold Design
Quality 2K Injection Mold Manufacturer, Affordable Price, Fast Delivery, Free Technical Support, Class A services.Contact us for the plastic injection molded part design optimization to lower your tooling and plastic part price Now！